Your Plumbing Crash Course: A Guide to Installing a Bathtub
Your Plumbing Crash Course: A Guide to Installing a Bathtub
Blog Article
What are your thoughts on How to Install a Bathtub?
Setting up a tub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old tub is readily available, the job can relocate rapidly; if you have to open up a wall to remove the old bathtub and also place the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will require an assistant to leave the old tub and also set in the new one. See to it you have actually qualified on your own for the job and are comfortable trying it. Rather than employing a service provider to take over a halfway-completed project, it is much better to take into consideration utilizing one before you begin. Opportunities are you might need a professional plumber to make tube connections.
This article will aid you mount a new tub in your restroom if you have actually currently bought a new tub as well as do not require to transform the plan of your previous water pipelines.
Your devices and also product checklist ought to comprise the following:
Preparing for the Setup
First of all, the sustaining framework provided with the bath must be fitted (if called for) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to see to it that if the faucet includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two taps using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you use every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The process of eliminating the existing taps can be rather bothersome because of the restricted access that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will certainly originate from the pipelines. Once the supply pipes have been removed, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any old securing substance.
Before moving on to fit the new faucets, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Setting up the Tub
Using the two wood boards under its feet, put the bathtub in the required placement. The wood boards are practical in evenly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four tiny points.
The next objective is to guarantee that the tub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bathtub until the spirit level reviews degree.
To mount faucets, fit the bottom of the outermost adaptable tap connector to the suitable supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Switch on the water supply and also inspect all joints as well as brand-new pipework for leaks and also tighten them if required. Load the bath tub and also examine the overflow outlet as well as the typical outlet for leakages.
Ultimately, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and also sealing around the tub ought to wait until the bath tub has actually been utilized a minimum of once as this will certainly settle it right into its final position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the placing opening in the bath/basin making sure that the washers are in area between the tap and also the sink. Protect the tap in place with the maker given backnut. As soon as the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The former type should be attached to the faucet ends initially, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to break a rigid seal, causing the water to penetrate the wall surface in between the bath as well as the tiling, resulting in complications with moisture and also feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components as well as fittings. They are offered in tubes and also cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill up the tub with water prior to sealing, to enable the motion experienced when the tub is in use. The sealer can crack fairly very early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also conveniently offered on the marketplace. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed our part on Installing A Bathtub. Thanks a ton for taking a few minutes to read through our post. Feel free to take the time to promote this post if you enjoyed it. Bless you for your time. Please check our blog back soon.
Plumbing woes? Connect. Report this page